Views: 0 Author: Site Editor Publish Time: 2020-11-19 Origin: Site
Many people know the variable Angle notching machine, because the variable Angle notching machine is widely used in various fields, but most people do not know the use and choosing method of the variable Angle notching machine, this article will take you to understand Use and choosing method of variable angle notching machine.
The following knowledge points are listed below:
Use of variable angle notching machine
Purpose of Variable Angle Notching Machine
Choosing methods of variable Angle notching machine
(1) the operation time concentration, strictly abide by the equipment operation rules, do safe operation.
(2) adjust the variable Angle notching machine before the primary blocking power supply.
(3) Make accurate adjustment according to the scale requirements of commodity specifications. Use special tools to be careful and pay attention to safety.
(4) Before operation, the feeder shall be adjusted to the same straight line and parallel to the operation axis.According to the width of the board to be cut, determine the board and two slotted wheel, and the bearing of each indentation roll.
(5) the installation of thin knife, to compact.Make sure that the blade radians and slotted wheel radians are the same, then tighten the platen screws.
(6) adjust the bottom shaft knife holder, pressure must not be too large.With the blade and cardboard after the touch of the stealthily intercept.Micro-adjustment to avoid damage to the knife seat and blade.When adjusted properly, there is no special need to move again.
(7) before opening the variable Angle notching machine, eradicate all the items on the variable Angle notching machine, check whether the fastener is loose and whether the chain is moderately tight.Then manually turn the car, check the knife device and feed paper indentation roller pressure is appropriate.No doubt with the crew after the staff played good hospitality, ready to boot.
(8) When starting up, after ensuring that the oil level of the oil cup is exposed properly, start the variable Angle notching machine and operate at a low speed.The investigation is not abnormal.Wait for each drive to be completely smooth, and the variable Angle notching machine to change without abnormal movement, and then improve the operation speed.The machine will stop for maintenance immediately.
(9) out of production, to try in advance.One after another to see a number of goods, admitted to meet the demand before the formal production.During the production process, pay attention to the investigation.Similar production process, review every 5 minutes.If any problem is found, stop the machine and adjust it immediately.
(10) often check whether the parts are worn or not to meet the demand, if in doubt, timely repair or replacement.
(11) Pay attention to machine maintenance and smooth.1. Ensure the oil level of the tank and drip frequently.2. Feed device drive slider is refueled once per shift;3. The connecting gears are often oiled and smooth.Operating bearings are maintained half a year to once a year.Fill with calcium base butter.
(12) The variable Angle notching machine is kept clean by scrubbing it regularly with oil.
(13) After production, stop the machine according to the rules and procedures.Block power supply.
1) variable Angle notching machine is used to cut metal plate with high cutting speed and high precision cutting.
2) Safe and reliable in performance
3) variable Angle notching machine is widely used in auto, ships, elevators, electrical equipment, pipelines, kitchen utensils, stainless steel products, and many other areas.
4) The variable Angle notching machine can be used to cut metal plate with high cutting speed and high precision cutting, the cutting machine can adjust according to thickness, safe and reliable in performance, widely used in auto, ships, elevators, electrical equipment, pipelines, kitchen utensils, stainless steel products, and many other area
First of all, pay attention to the following points
(1) Before the selection of the first to work according to the type of variable Angle notching machine
(2) Weight of variable Angle notching machine.This weight is not for you to weigh.Instead, pick it up and feel the weight.The heavier one is better than the lighter one.
(3) Brand selection.Our popular understanding, good brand technology mature and stable.
(4) Select according to wattage of variable Angle notching machine.The e figure of 800w can satisfy many USES.I'm going to go 750 minus 1100
After the above options can be plugged in to meet the test.Test variable Angle notching machine mainly look and listen to the sound.Whether the sound is smooth in the rotation, whether there is a nap, more kakaka sound.You can hear that.If there is, the variable Angle notching machine can't be solved, it will break down in a few days. This is the most important point, which determines the service life of the variable Angle notching machine.A more important point to test the variable Angle notching machine is to see whether sparks are coming from the side vents of the carbon brush.This machine must not be bought if it sparks.
I hope this article is helpful for you to understand the variable Angle notching machine. Our company is specialized in producing the variable Angle notching machine. If you need variable Angle notching machine, Press Brake, Shearing Machine please remember to contact us.Both the variable Angle notching machine and the service will keep you happy.
